Monoblock Duo LNBF 4 Degree Dual Output Linear KU 0.4 dB (KLB2)

Description

Send to friend

Reviews

You want to receive signal from two satellites at the same time?

The Sadoun DUO LNBF is a Monoblock KU-band linear LNBF for digital satellite reception of two satellites separated by 4 degrees on the Clarke Belt arc. It is commonly used with Satellites 101W and 97W, or 97W and 93W.

It will work with offset dishes between 60cm (23.6") to 90cm (36"). It has two outputs so that you can hook more than one receiver to the LNBF.

The LNBF on each side of this Monoblock Duo is a UNIVERSAL type. The built-in DiSEqC switch allows the receiver to switch between the two satellites instantly. This is used for Free To Air satellite reception in North America. Compatible with all FTA satellite receivers on the market today. Works with for all KU band reception except DSS. Great choice for Galaxy 25 and AMC4 simultaneous reception. Or Galaxy 25 & Galaxy 26 reception.

FEATURES::

Dual Output LNBF
Lightweight and small size for easy installation
Covers Ku Band Satellite Frequencies 10.7-12.75 GHz
0.4 dB low noise figure for improved signal reception (specially on weak signal) and low interference.
Voltage-Controlled H/V Switching (13/18 V)
Comes with an adapter for any dish with LNBF holder standard 40mm diameter. Thus allowing this LNB to be mounted effortlessly on almost any offset dish, such as Fortec Star 80,90cm dishes. Black LNBF Holder you see in the picture above is not included.
Linear type.
COMPATIBLE WITH ALL FTA SYSTEMS RELATED TO Galaxy 25 (97W), G3C (95W), Galaxy 10R (123W), AMC4 (101W), and more.

Installation Instructions:

Place LNBF1 in the focal point of your dish using the Dish's LNBF holder.
Connect an RG6 coaxial cable between receiver 1 and LNBF Monoblock Output 1
Connect an RG6 coaxial cable between receiver 2 and LNBF Monoblock Output 2
Set the DiSEqC switch position in each receiver as follows:
Command 1 or A for LNBF1 (i.e. 97W or whichever the Western satellite you pick)
Command 2 or B for LNBF2 (i.e. 93W or whichever the Eastern satellite you pick)
Optimize the signal strength and quality for LNBF1.
Optimize the signal strength and quality for LNBF2 by turning it a little upwards or downwards a few degrees.
Note:
This Sadoun Monoblock DUO LNBF is designed to work with One or Two DVB receivers to receive signal from two satellites using one stationary dish.

Specification	Value
Input Frequency Range	10.7 ~ 12.75 GHz
Output Frequency Range	950 ~ 1450 MHz
LO Frequency	9750/10600 GHz
Conversion Gain	56 dB
Cross Pol. Isolation	25 dB
F/D Ratio	0.6
Noise Figure	0.4 dB Typ (0.8db Max)
Load Impedance	75 ohm
Input Reflector Type	Offset
Gain Flatness	5 dBpp over operating band +/- 0.5 dBpp H/V.Pol @ 27 MHz
L.O. Frequency Stability: (+25°C)	+/- 1 MHz
(-40°C ~ +60°C)	+/- 3 MHz
L.O. Phase Noise: (1 KHz Offset)	-59 dBc/Hz
(10 KHz Offset)	-84 dBc/Hz
(100 KHz Offset)	-101 dBc/Hz
L.O. Spurious	-60 dBm
Omage Rejection	40 dB min
Output VSWR	2.0:1
Output Connector	75Ohm F Type Female
D.C. Power Supply	11.5 – 19 V
Current consumption	90 mA Typ., 110 mA Max
Polar Switching Voltage	Vertical: 10.5 ~ 14.5 V Horizontal: 15.5 ~ 21 V
Operating Temperature	-40°C ~ +60°C